大家知道研磨機的種類很多，并且陶瓷是研磨機制成的重要材料之一。還有一種常見的研磨機叫做陶瓷研缽式研磨機，陶瓷研缽式研磨機的組成很簡單，主要有研磨棒和陶瓷研缽這兩者組成的，那么這兩者是怎樣安裝的?陶瓷研磨棒，將陶瓷研棒本身所配套使用的有一個專用螺釘，把螺釘擰進陶瓷研棒內螺的紋路孔中，適量的擰緊，也不要太過于緊。設備上裝置了一個橡膠的緩沖墊板，而陶瓷研缽則放在該墊的中央位置上，然后用3件螺桿筆直的立起來后把壓圈壓住在研缽上并且將其固定壓緊。同樣也可以用瑪瑙研棒，具體的操作方法與陶瓷研磨棒相同。
因為研磨棒所安裝們置在該機器的擺臂上，由于擺臂是固定的并且是在研磨棒上的動力頭輸出軸的位置上，研磨棒動力頭所安裝的位置是在一個可以上下活動的滑動座上，這樣螺桿就可以調節滑座，從而可以上下的移動。在研磨機進行工作時，研磨棒的動力頭被快速的轉動起來，并且研磨棒也隨著被轉動?？梢愿鶕枰_到的研磨效果來確定研磨棒和研缽的位置，松緊情況根據實際情況而定。如果位置被確定下來，操作者在上移研磨棒完成后，然將研缽安裝好，接著應轉動手輪再將研磨棒總成停留在原來的高度位置上，必要時可以做位置記號。
中譯英：
We know that many kinds of grinding machine, grinding machine made and the ceramic is one of important material. There is also a common grinding machine called ceramic mortar type grinding machine, ceramic mortar type grinding machine composition is simple, mainly a grinding rod ceramic mortar and the combination of both, so both of which is how to install? Ceramic grinding rods, ceramic pestle itself by supporting the use of a special screw, the the screw is screwed into the ceramic pestle inner screw line hole, proper tightening, also not too tight. A device of a rubber cushion board, ceramic mortar on the pad of the central position, and then use the 3screw straight up after the pressure ring presses in mortar and the fixing and pressing. Can also use the agate pestle, specific operation method and ceramic grinding rod is the same.
Because the grinding rod installation are arranged in the machine on the swing arm, the swing arm is fixed and is in the grinding power head rod on the position of the output shaft, a grinding rod power head mounting position is in a can move up and down sliding seat, so that the screw can adjust the sliding seat, which can move under. In the grinding machine working, the grinding rod power head is fast turning up, and also as the grinding rod is rotated. According to the need to achieve the grinding effect to determine the pestle and mortar positions, the tightness according to actual circumstances. If the location is determined, the operator moves the grinding rod in complete, but will mortar installed, then we should turn the handwheel to the grinding rod assembly stay the same height position, when necessary, can do position mark.
(圖/文http://www.zdrav.cn/)
加入收藏
